TMM 80063-3 for Cars X2-SERIES PRO
1000A burst ESC!
| TMM 80063-3 for Cars X2-SERIES PRO | 1 861,85 € |
| 2 cooling FANs XXL | 34,95 € |
| power cables 10.0 mm2 (8 AWG) | 14,95 € |
| Increased humidity protection | 8,95 € |
| ON/OFF switch | 1,95 € |
| Price total excl. VAT | 1 922,65 € |
Make your own custom configuration that fits your model. Choose from multiple add-ons and stand out from the crowd.
CONFIGURE YOUR OWN
Insane power. For everything.
TMM 80063-3 was designed to push the limits and leave the competition behind. This speed controller is the most powerful thing you can get for your RC project. With 1000 [A] of peak currents, 800 [A] continuous and possibility of running up to 15S we made sure you will never be behind.
Advanced Programming
Thanks to our free PC application CONTROLLERS 2 you are able to discover the new possibilities of your model. Finding the best settings for your RC model has never been so exciting! Change over 50 parameters, upgrade firmware or check relevant data from the run.
To connect ESC with PC you need USBCOM5 and CC_11 cable.
| Possibility of cells temperature measuring (cells protection) | |
| Number of cells | 4 - 15 |
| Switching HV-BEC voltage | V |
| Possibility of very powerful switching BECs | |
| BEC short circuit protection | |
| Possibility of setting an amount of residual energy for BEC | |
| Model Type | For cars |
| Switching S-BEC voltage | V |
| Max. BEC current at 25 °C | A |
| Possibility of setting the voltage of BEC | |
| Max. peak current | 1000A |
| Possibility of setting RPM limits (motor protection) | |
| Number of regulation steps | 2048 |
| Possibility of automatic setting of cut off voltage | |
| On-state switch (FETs) resistance at 25 °C | 2 mW |
| Manually set type of cells | |
| Dimensions | see guide |
| Possibility of manually set timing | |
| Weight without power conductors | 1200 gram |
| Active free-wheeling circuit ON / OFF | |
| Power conductors cross-section to batt. / to mot. | see guide |
| Adjustable acceleration speed | |
| Servocable cross-section | 0.25 mm2 |
| Software reversal of rotation | |
| Possibility of design with external heatsinks | |
| False-start protection | |
| Possibility of design with external heatsinks + FAN | |
| Temperature fuse of the controller | |
| Possibility of WR version (full protection against water) | |
| Software updates available through internet | |
| Reversible controller (both-way mode) | |
| Programming using PC | |
| Brake ON / OFF | |
| ABS simulation | |
| Possibility of setting brake ramps | |
| Possibility of automatic braking in neutral throttle position | |
| Possibility of connecting braking lights | |
| Telemetry (real-time back data transfer) | |
| Possibility of operation also with sensors motors | |
| 32-BIT SYSTEM | |
| Operating voltage | 12 - 63 V |
| "One-way" mode | |
| Very high resistance against overloading | |
| Compatible with all types of feeding cells | |
| Max. continuous current | 800A |
| Possibility of motor temperature measuring (motor protection) | |
| Available BEC / OPTO versions | |
| Possibility of setting current limits | |
| Possibility of setting switching off voltage | |
| Motor PWM frequency | 8 kHz |
| Possibility of manually set number of cells | |
| Max. RPM | 200000 |
| Automatically set timing | |
| Dimensions with external capacitor | see guide |
| Possibility of automatic setting of throttle limits | |
| Weight incl. all conductors | see guide |
| External signalization of important states | |
| Length of the power conductors | see guide |
| Empty batt. behaviour - motor power reduction | |
| Length of the servocable | 190 mm |
| Masking of interference | |
| Possibility of design with water-cooled heatsinks | |
| Current fuse of the controller | |
| Possibility of WP version (increased protection against water) | |
| ACR - Automatic Current Reduce | |
| Possibility of design with ON/OFF switch (connected safely) | |
| Bidirectional "both-way" mode | |
| Reading-out of data from the controller using PC | |
| Possibility of switching reversible controller into "one-way" mode | |
| ICS-2 connector - super-fast PC connection link | |
| Proportional brake | |
| Possibility of setting brake intensity | |
| Possibility of setting neutral brake ramps | |
| Setting of the range of neutral zone | |
| Internal Data Logger (data recorder) | |
| Real-time Monitoring (PC or other device) | |
| Automatic Sensor Setting | |
| Number of NiCd, NiMh feeding cells | 15 |
| 4 Memory Banks | |
| Plug and Play (functional immediately without the need for additional programming) | |
| Number of A123 feeding cells | 5 |
| Outstanding cells management |
Get the full advantage of our 30 years of experience with producing ESCs for both, industrial and modellers customers. X2-SERIES controllers are fully programmable and adjustable for any RC model. You can use our own PC software to adjust the parameters and reading out the history logs of your runs as well. With X2-SERIES controllers you will be able to find the most efficient setup. Developed with RC modellers in mind, we used our experience from various industrial projects to create reliable ESCs with sophisticated system of fuses for the safety of your model. This comes backed by 3 years warranty.
More info
